-- *******************************************************************
-- CISCO-WDS-INFO-MIB.my
-- September 2005, Young Il Choi
--
-- Copyright (c) 2005-2006 by Cisco Systems, Inc.
-- All rights reserved.
-- *******************************************************************
--CISCO-WDS-INFO-MIB DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,NOTIFICATION-TYPE,OBJECT-TYPE,Unsigned32,Counter32,Gauge32FROM SNMPv2-SMI
MODULE-COMPLIANCE,
NOTIFICATION-GROUP,OBJECT-GROUPFROM SNMPv2-CONF
MacAddress,TimeStamp,DateAndTime,TEXTUAL-CONVENTIONFROM SNMPv2-TC
InetAddressType,InetAddressFROM INET-ADDRESS-MIB
SnmpAdminStringFROM SNMP-FRAMEWORK-MIB
CDot11SsidString,
CDot11SecAuthKeyMgmtType
FROM CISCO-DOT11-SSID-SECURITY-MIB
CDot11IfVlanIdOrZero
FROM CISCO-DOT11-IF-MIB
ciscoMgmt
FROM CISCO-SMI;--********************************************************************
--* MODULE IDENTITY
--********************************************************************ciscoWdsInfoMIB MODULE-IDENTITYLAST-UPDATED"200509150000Z"
ORGANIZATION"Cisco Systems Inc."CONTACT-INFO" Cisco Systems,
Customer Service
Postal: 170 West Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-dot11@cisco.com"DESCRIPTION"This MIB is intended to be implemented on all Cisco
network entities that provide Wireless Domain Services
(WDS). The WDS provides a control mechanism for
wireless devices that roam between Access Points
residing on different layer 3 subnets. When WDS is in
the Wireless LAN Services Module(WLSM), the access
points providing Layer 3 mobility must register with
the WDS before wireless devices are given access to the
mobility network. The location of the WDS is specified
in each Access Point along with LEAP device credentials
that are required for authentication with the WDS. Once
the Access Point and the Mobile Node are authenticated
with the WDS, those are considered registered.
This MIB reports the information about the Wireless
Domain Servers, Access Points, Mobile Nodes, and their
roaming patterns.
GLOSSARY
AAA
Authentication, Authorization, Accounting
Access Point (AP)
An entity that contains an 802.11 medium access
control (MAC) and physical layer (PHY) interface
and provides access to the distribution services via
the wireless medium for associated devices.
BSSID
Basic Service Set Identification, where the basic
service set is defined as the set of data transfer
rates that all the stations in a BSS will be capable
of using to receive frames from the wireless medium.
CCKM
Cisco Central Key Management.
Context
The mobility context for a Mobile Node includes its
current mobility bindings with the Access Points,
IP/802 address bindings, cached configuration
parameters, QoS state, IP group membership,
authentication state, accounting statistics, and
other dynamically derived protocol state information.
EAP
Extensible Authentication Protocol.
Hot Standby Router Protocol (HSRP)
Cisco Hot Standby Router Protocol as defined in RFC2281
L3MM
Layer-3 Mobility Manager (L3MM) is a new software
entity residing on Central Switch (CS). L3MM maintains
the mobility database and manages mGRE tunnels and
tunnel paths to provide L3 Mobility for wireless
clients.
Layer 3 Mobility Control Protocol (LCP)
A simple protocol to exchange control message between
WDS and L3MM to achieve layer 3 seamless mobility for
wireless devices.
mGRE Tunnels
Multipoint Generic Routing Encapsulation tunnels. This
tunnel is used to tunnel wireless traffic and used to
transfer wireless traffic between AP and CS.
MIC
Message Integrity Check. A MIC can, optionally,
be added to WEP-encrypted 802.11 frames.
Mobile Node (MN)
A roaming 802.11 wireless device in a wireless
network associated with an Access Point.
SSID
Service Set Identification, where the station service
is defined as the set of services that support
transport of medium access control (MAC) service data
units (MSDUs) between stations within a basic service
set.
TKIP
WPA Temporal Key encryption.
Wireless Domain Services (WDS)
The set of services being offered at a particular
broadcast domain that may be an IP subnet or a
particular VLAN, or across the L3 cloud. The services
include the following.
1. Fast Secure Roaming with CCKM.
2. Layer 3 seamless mobility.
3. Radio Management aggregation for 802.11 wireless
clients .
WDS Entity
The logical entity that resides in an infrastructure
node and offers WDS to the descendants of that
infrastructure node in the wireless services
hierarchy.
WEP
Wired Equivalent Privacy. This is generally used
to refer to 802.11 legacy encryption.
WLSM
Wireless LAN Services Module
Wireless Network Manager (WNM)
The network management system that manages the
entire hierarchy of devices providing WDS.
WPA
WiFi Protected Access."REVISION"200509150000Z"DESCRIPTION"Initial version of this MIB module."::={ ciscoMgmt 509}ciscoWdsInfoMIBNotifs OBJECTIDENTIFIER::={ ciscoWdsInfoMIB 0}
ciscoWdsInfoMIBObjects OBJECTIDENTIFIER::={ ciscoWdsInfoMIB 1}ciscoWdsInfoMIBConform OBJECTIDENTIFIER::={ ciscoWdsInfoMIB 2}ciscoWdsInfoMacAuthCache OBJECTIDENTIFIER::={ ciscoWdsInfoMIBObjects 1}ciscoWdsInfoAccessPoint OBJECTIDENTIFIER::={ ciscoWdsInfoMIBObjects 2}ciscoWdsInfoMobileNode OBJECTIDENTIFIER::={ ciscoWdsInfoMIBObjects 3}ciscoWdsInfoNetworkManager OBJECTIDENTIFIER::={ ciscoWdsInfoMIBObjects 4}ciscoWdsInfoStatistics OBJECTIDENTIFIER
::={ ciscoWdsInfoMIBObjects 5}ciscoWdsInfoMobility OBJECTIDENTIFIER::={ ciscoWdsInfoMIBObjects 6}ciscoWdsInfoRoamStatistics OBJECTIDENTIFIER::={ ciscoWdsInfoMIBObjects 7}-- Textual ConventionsCWdsClientTrackingStatus ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"These are the Client Tracking statuses on WDS. The
Client Tracking feature expands the radio management
information gathered from Access Points to include
information on Mobile Node authentication and roaming
events. The WDS collects those data and sends to
Network Manager. This feature provides near-real-time
tracking of Mobile Node associations via the Network
Manger.
active - Enabled and collecting the data,
inactive - Enabled but not collection the data,
disabled - The Client Tracking is disabled."SYNTAXINTEGER{active(1),inactive(2),disabled(3)}CWdsDeviceAuthType ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"These are the IEEE 802.11 supported authentication
methods for WDS devices such as Access Points, Mobile
Nodes and Wireless Network Managers:
open - Open System authentication,
shared - Shared authentication,
leap - Cisco Light-weight EAP,
eap - EAP authentication,
mac - MAC authentication,
macOrEap - MAC or EAP authentication,
macOrLeap - MAC or LEAP authentication,
eapOptional - Eap Optional."SYNTAXBITS{
open(0),shared(1),leap(2),eap(3),mac(4),macOrEap(5),macOrLeap(6),eapOptional(7)}CWdsDeviceState ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"The registration state of the network entities
requiring the WDS services.
unknown - Unknown state,
initial - Initial state,
authInProgress - Authentication is in progress,
authFailed - Authentication is failed,
authenticated - Authentication is successful,
securityKeysSetup - Security keys are set,
registered - Registration is completed,
detached - The device is detached."SYNTAXINTEGER{unknown(1),initial(2),authInProgress(3),authFailed(4),authenticated(5),securityKeysSetup(6),registered(7),detached(8)}
--********************************************************************
--* WDS AAA Mac Cache identification parameters
--********************************************************************cwdsiMacAuthCacheTable OBJECT-TYPESYNTAXSEQUENCEOF CwdsiMacAuthCacheEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table provides the information about the MAC
addresses cached in the WDS for MAC authentication.
MAC authentication caching reduces overhead because
the WDS authenticates devices in its MAC-address
cache without sending the request to the
authentication server.
An entry is added to this table when a Mobile Node
completes MAC authentication to the authentication
server. An entry is removed if the MAC address is not
flushed before timeout."::={ ciscoWdsInfoMacAuthCache 1}cwdsiMacAuthCacheEntry OBJECT-TYPESYNTAX CwdsiMacAuthCacheEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"Each entry is a set of a MAC address and age for
fast MAC authentication."INDEX{ cwdsiMacAuthCacheMacAddr }::={ cwdsiMacAuthCacheTable 1}
CwdsiMacAuthCacheEntry ::=SEQUENCE{
cwdsiMacAuthCacheMacAddr MacAddress,
cwdsiMacAuthCacheAge Unsigned32}cwdsiMacAuthCacheMacAddr OBJECT-TYPESYNTAXMacAddressMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object specifies the MAC address of the device
which is cached in the WDS for MAC authentication."::={ cwdsiMacAuthCacheEntry 1}
cwdsiMacAuthCacheAge OBJECT-TYPESYNTAXUnsigned32UNITS"minutes"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the elapsed time since the MAC
address has been cached. If the MAC address is not
flushed within the specific time(default 30 minutes),
the entry with cwdsiMacAuthCacheMacAddr is removed."::={ cwdsiMacAuthCacheEntry 2}--********************************************************************
--* WDS Access Point identification parameters
--********************************************************************cwdsiApTable OBJECT-TYPESYNTAXSEQUENCEOF CwdsiApEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table provides the information about the Access
Points registered with WDS.
An entry is added to this table when a Access Point
register with WDS and the entry is removed after the
lifetime of the Access Point expires."::={ ciscoWdsInfoAccessPoint 1}cwdsiApEntry OBJECT-TYPESYNTAX CwdsiApEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry is a set of attributes of an Access Point
currently registered with WDS."INDEX{ cwdsiApMacAddr }::={ cwdsiApTable 1}
CwdsiApEntry ::=SEQUENCE{
cwdsiApMacAddr MacAddress,
cwdsiApAddrType InetAddressType,
cwdsiApAddr InetAddress,
cwdsiApName SnmpAdminString,
cwdsiApState CWdsDeviceState,
cwdsiApLifeTime Unsigned32,
cwdsiApNeighborAddrType InetAddressType,
cwdsiApNeighborAddr InetAddress,
cwdsiApNeighborName SnmpAdminString,
cwdsiApNeighborPortName SnmpAdminString}cwdsiApMacAddr OBJECT-TYPESYNTAXMacAddressMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The MAC address of the Access Point."::={ cwdsiApEntry 1}cwdsiApAddrType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"Represents the type of Internet address stored in the
corresponding instance of the cwdsiApAddr."::={ cwdsiApEntry 2}cwdsiApAddr OBJECT-TYPESYNTAXInetAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The Internet address of the Access Point."::={ cwdsiApEntry 3}cwdsiApName OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the hostname of the Access
Point."::={ cwdsiApEntry 4}cwdsiApState OBJECT-TYPESYNTAX CWdsDeviceState
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the registration state of the
Access Point with the WDS."::={ cwdsiApEntry 5}cwdsiApLifeTime OBJECT-TYPESYNTAXUnsigned32UNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the maximum time after which
the registration of the Access Point with WDS expires.
The Access Point must re-register before the lifetime
is exhausted, otherwise it will be deleted from the
table."::={ cwdsiApEntry 6}cwdsiApNeighborAddrType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-only
STATUScurrentDESCRIPTION"Represents the type of Internet address stored in the
corresponding instance of the cwdsiApNeighborAddr."::={ cwdsiApEntry 7}cwdsiApNeighborAddr OBJECT-TYPESYNTAXInetAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The Internet address of the network entity with which
the Ethernet port of the Access Point is directly
connected."::={ cwdsiApEntry 8}cwdsiApNeighborName OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the hostname of the network
entity with which the Ethernet port of the Access Point
is directly connected."::={ cwdsiApEntry 9}cwdsiApNeighborPortName OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the port name of the network
entity with which the Ethernet port of the Access Point
is directly connected. This will typically be the value
of the ifName object (e.g., 'Ethernet0')."::={ cwdsiApEntry 10}--********************************************************************
--* WDS Mobile Node identification parameters
--********************************************************************cwdsiMnTable OBJECT-TYPESYNTAXSEQUENCEOF CwdsiMnEntry
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"This table provides the information about the Mobile
Nodes registered with WDS.
An entry is added to this table when a Mobile Node
registers with WDS and the entry is removed after the
lifetime of the Mobile Node expires."::={ ciscoWdsInfoMobileNode 1}cwdsiMnEntry OBJECT-TYPESYNTAX CwdsiMnEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry is a set of attributes of a Mobile Node
currently registered with WDS."INDEX{ cwdsiMnMacAddr }::={ cwdsiMnTable 1}
CwdsiMnEntry ::=SEQUENCE{
cwdsiMnMacAddr MacAddress,
cwdsiMnAddrType InetAddressType,
cwdsiMnAddr InetAddress,
cwdsiMnApMacAddr MacAddress,
cwdsiMnApAddrType InetAddressType,
cwdsiMnApAddr InetAddress,
cwdsiMnMobilityNetworkId Unsigned32,
cwdsiMnState CWdsDeviceState,
cwdsiMnSsid CDot11SsidString,
cwdsiMnBssid MacAddress,
cwdsiMnVlan CDot11IfVlanIdOrZero,
cwdsiMnKeyMgmt CDot11SecAuthKeyMgmtType,
cwdsiMnAuthType CWdsDeviceAuthType,
cwdsiMnUptime TimeStamp,
cwdsiMnLifetime Unsigned32}cwdsiMnMacAddr OBJECT-TYPESYNTAXMacAddressMAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"The MAC address of the Mobile Node."::={ cwdsiMnEntry 1}cwdsiMnAddrType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Represents the type of Internet address stored in the
corresponding instance of the cwdsiMnAddr."::={ cwdsiMnEntry 2}cwdsiMnAddr OBJECT-TYPESYNTAXInetAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The Internet address of the Mobile Node."::={ cwdsiMnEntry 3}cwdsiMnApMacAddr OBJECT-TYPESYNTAXMacAddress
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The MAC address of the Access Point with which the
Mobile Node is associated."::={ cwdsiMnEntry 4}cwdsiMnApAddrType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Represents the type of Internet address stored in the
corresponding instance of the cwdsiMnApAddr."::={ cwdsiMnEntry 5}cwdsiMnApAddr OBJECT-TYPESYNTAXInetAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The Internet address of the Access Point with which
the Mobile Node has associated."::={ cwdsiMnEntry 6}cwdsiMnMobilityNetworkId OBJECT-TYPESYNTAXUnsigned32(1..4096)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the mobility network-id of the
Mobile Node."::={ cwdsiMnEntry 7}cwdsiMnState OBJECT-TYPESYNTAX CWdsDeviceState
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the registration state of the
Mobile Node with WDS."::={ cwdsiMnEntry 8}cwdsiMnSsid OBJECT-TYPE
SYNTAX CDot11SsidString
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the SSID with which the Mobile
Node has associated with the Access Point."::={ cwdsiMnEntry 9}cwdsiMnBssid OBJECT-TYPESYNTAXMacAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the BSSID used by the Mobile
Node to communicate with the Access Point."::={ cwdsiMnEntry 10}cwdsiMnVlan OBJECT-TYPESYNTAX CDot11IfVlanIdOrZero
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the VLAN ID used by Access Point
to bridge trunk that carries the traffic, when the
Mobile Node associates with Access Point specified by
cwdsiMnApAddr, using SSID specified by cwdsiMnSsid."::={ cwdsiMnEntry 11}cwdsiMnKeyMgmt OBJECT-TYPESYNTAX CDot11SecAuthKeyMgmtType
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the type of authenticated key
management. If none of the bit is set, no key
management is used."::={ cwdsiMnEntry 12}cwdsiMnAuthType OBJECT-TYPESYNTAX CWdsDeviceAuthType
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies one of the pre-defined
authentication algorithms and additional
authentication procedures for the Mobile Node.
When the cwdsiMnState is 'registered', the valid
combination of the authentications are:
- open(0),
- shared(1),
- leap(2),
- eap(3),
- mac(4),
- open(0) and eap(3),
- open(0) and mac(4),
- open(0), eap(3) and mac(4),
- open(0) and macOrEap(5),
- shared(1) and eap(3),
- shared(1) and mac(4),
- shared(1), eap(3) and mac(4),
- mac(4) and leap(2).
Otherwise, the valid combination of the
authentications are:
- eap(3),
- mac(4),
- eap(3) and mac(4),
- macOrEap(5),
- leap(2),
- mac(4) and leap(2),
- macOrLeap(6),
- eapOptional(7).
If none of the bits are set, there is no run-time
authentication."::={ cwdsiMnEntry 13}cwdsiMnUptime OBJECT-TYPESYNTAXTimeStampMAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"This object specifies the value of sysUpTime at the
time this Mobile Node registered with WDS."::={ cwdsiMnEntry 14}cwdsiMnLifetime OBJECT-TYPESYNTAXUnsigned32UNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the maximum time after which the
registration of the Mobile Node with its WDS expires.
The Mobile Node must re-register before the time
expires, otherwise it will be deleted from the table."::={ cwdsiMnEntry 15}--********************************************************************
--* WDS Wireless Network Manager identification parameters
--********************************************************************cwdsiWnmTable OBJECT-TYPESYNTAXSEQUENCEOF CwdsiWnmEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table provides the information about the Wireless
Network Managers configured on WDS. WDS provides an
aggregation point of all radio management traffic from
participating Access Points to the registered Wireless
Network Manager. The entry also provides the statistics
between WDS and Wireless Network Manager.
An entry is added to this table when a Wireless Network
Manager is configured on WDS. Currently WDS supports
just one Wireless Network Manger."::={ ciscoWdsInfoNetworkManager 1}cwdsiWnmEntry OBJECT-TYPESYNTAX CwdsiWnmEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry is a set of attributes of a Wireless
Network Manger and statistics.
The statistics is gathered since the Wireless
Network Manager has been registered with WDS."INDEX{ cwdsiWnmAddrType,
cwdsiWnmAddr }::={ cwdsiWnmTable 1}
CwdsiWnmEntry ::=SEQUENCE{
cwdsiWnmAddrType InetAddressType,
cwdsiWnmAddr InetAddress,
cwdsiWnmState CWdsDeviceState,
cwdsiWnmLinkStatus INTEGER,
cwdsiWnmClientTracking CWdsClientTrackingStatus,
cwdsiWnmReqMsgCount Counter32,
cwdsiWnmSentMsgCount Counter32,
cwdsiWnmRetryTxMsgCount Counter32,
cwdsiWnmWaitingAckMsgCount Counter32,
cwdsiWnmDropMicTxMsgCount Counter32,
cwdsiWnmDropUmdTxMsgCount Counter32,
cwdsiWnmIndicatedMsgCount Counter32,
cwdsiWnmRxMsgCount Counter32,
cwdsiWnmDropRxMsgCount Counter32,
cwdsiWnmDiscontinuityTime TimeStamp}cwdsiWnmAddrType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Represents the type of Internet address stored in the
corresponding instance of the cwdsiWnmAddr."::={ cwdsiWnmEntry 1}cwdsiWnmAddr OBJECT-TYPESYNTAXInetAddress(SIZE(0..36))MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"The Internet address of the Wireless Network Manager."::={ cwdsiWnmEntry 2}cwdsiWnmState OBJECT-TYPESYNTAX CWdsDeviceState
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the registration state of the
Wireless Network Manger with WDS."::={ cwdsiWnmEntry 3}cwdsiWnmLinkStatus OBJECT-TYPESYNTAXINTEGER{up(1),down(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"This object specifies the link status between WDS and
Wireless Network Manager."::={ cwdsiWnmEntry 4}cwdsiWnmClientTracking OBJECT-TYPESYNTAX CWdsClientTrackingStatus
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the status of Client Tracking on
WDS."::={ cwdsiWnmEntry 5}cwdsiWnmReqMsgCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of messages that are
supposed to be sent to Wireless Network Manger.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiWnmDiscontinuityTime."
::={ cwdsiWnmEntry 6}cwdsiWnmSentMsgCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of sent messages by
WDS to Network Manger.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiWnmDiscontinuityTime."::={ cwdsiWnmEntry 7}cwdsiWnmRetryTxMsgCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of transmitted
messages by WDS to Network Manger after more than one
retransmission.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiWnmDiscontinuityTime."::={ cwdsiWnmEntry 8}cwdsiWnmWaitingAckMsgCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of sent messages by
WDS and waiting for acknowledge response from Wireless
Network Manger.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiWnmDiscontinuityTime."::={ cwdsiWnmEntry 9}cwdsiWnmDropMicTxMsgCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"This object specifies the number of dropped messages
by WDS because of Message Integrity Check (MIC) failure
before sending the messages to Wireless Network
Manger.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiWnmDiscontinuityTime."::={ cwdsiWnmEntry 10}cwdsiWnmDropUmdTxMsgCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of dropped messages
by WDS because of the Unacknowledged Message
Descriptor (UMD) allocation problem before sending the
messages to Wireless Network Manger.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiWnmDiscontinuityTime."::={ cwdsiWnmEntry 11}
cwdsiWnmIndicatedMsgCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of indicated messages
to WDS before receiving the messages from Wireless
Network Manager.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiWnmDiscontinuityTime."::={ cwdsiWnmEntry 12}cwdsiWnmRxMsgCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of received messages
by WDS after receiving the messages from Wireless
Network Manager.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiWnmDiscontinuityTime."::={ cwdsiWnmEntry 13}cwdsiWnmDropRxMsgCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of messages dropped
by WDS received from Wireless Network Manager.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiWnmDiscontinuityTime."::={ cwdsiWnmEntry 14}cwdsiWnmDiscontinuityTime OBJECT-TYPESYNTAXTimeStampMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the vaule of sysUpTime on the
most recent occassion when the WNM is registered with
WDS."::={ cwdsiWnmEntry 15}--********************************************************************
--* WDS Statistics identification parameters
--********************************************************************cwdsiApNum OBJECT-TYPESYNTAXGauge32UNITS"access-points"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of Access Points
currently registered with this WDS."::={ ciscoWdsInfoStatistics 1}cwdsiMnNum OBJECT-TYPESYNTAXGauge32UNITS"mobile-nodes"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"This object specifies the number of Mobile Nodes
currently registered with this WDS."::={ ciscoWdsInfoStatistics 2}cwdsiAaaAuthAttemptCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of AAA authentication
attempts (such as LEAP) made by WDS to authenticate
Access Points and Mobile Nodes.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS."::={ ciscoWdsInfoStatistics 3}cwdsiAaaAuthSuccessCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of successful AAA
authentication successes made by WDS to authenticate
Access Points and Mobile Nodes.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS."::={ ciscoWdsInfoStatistics 4}cwdsiAaaAuthFailureCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of failed AAA
authentication attempts made by WDS to authenticate
Access Points and Mobile Nodes.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS."::={ ciscoWdsInfoStatistics 5}cwdsiMacSpoofingBlockCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"This object specifies the number of MAC Spoofing
attempts detected and blocked by WDS.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS."::={ ciscoWdsInfoStatistics 6}cwdsiRoamsWithoutAaaAuthCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of roams not
involving AAA authentication.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS."::={ ciscoWdsInfoStatistics 7}cwdsiRoamsWithFullAaaAuthCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of roams involving
full AAA authentication.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS."::={ ciscoWdsInfoStatistics 8}cwdsiRoamsFastSecuredCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of fast and secured
roams with CCKM.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS."::={ ciscoWdsInfoStatistics 9}cwdsiMscMismatchCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of Message Sequence
Counter (MSC) mismatches.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS."::={ ciscoWdsInfoStatistics 10}cwdsiKscFailureCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of failures for Key
Sequence (KSC) with which WDS authenticates the Mobile
Node for Fast Secure Roaming.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS."::={ ciscoWdsInfoStatistics 11}cwdsiMicFailureCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of Message Integrity
Check (MIC) failures detected by WDS.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS."::={ ciscoWdsInfoStatistics 12}cwdsiRnMismatchCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of mismatches for
ReKey Number (RN) with which WDS authenticates the
Mobile Node for Fast Secure Roaming.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS."::={ ciscoWdsInfoStatistics 13}--********************************************************************
--* WDS Mobility identification parameters
--********************************************************************cwdsiLcpStatus OBJECT-TYPESYNTAXINTEGER{
down(1),up(2),inTransition(3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the LCP link status. LCP is a
communication protocol between WDS residing on WLSM and
L3MM on RP to provide L3MM with up-to-date information
about current location of Mobile Node and also to
propagate tunnel end point and other configuration
information from RP to WDS/AP.
down(1) - The LCP link status is down,
up(2) - The LCP link status is up,
inTransition(3) - The LCP link status is in
transition from up(2) to down(1)
or from down(1) to up(2)."::={ ciscoWdsInfoMobility 1}cwdsiCsMgmtAddrType OBJECT-TYPE
SYNTAXInetAddressTypeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Represents the type of Internet address stored in the
corresponding instance of the cwdsiCsMgmtAddr."::={ ciscoWdsInfoMobility 2}cwdsiCsMgmtAddr OBJECT-TYPESYNTAXInetAddress(SIZE(0..36))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The Internet address of the Central Switch
Management."::={ ciscoWdsInfoMobility 3}cwdsiWdsAddrType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-only
STATUScurrentDESCRIPTION"Represents the type of Internet address stored in the
corresponding instance of the cwdsiWdsAddr."::={ ciscoWdsInfoMobility 4}cwdsiWdsAddr OBJECT-TYPESYNTAXInetAddress(SIZE(0..36))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The Internet address of the network device in which
WDS resides."::={ ciscoWdsInfoMobility 5}cwdsiWdsHsrpVirtualAddrType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"Represents the type of Internet address stored in the
corresponding instance of the cwdsiWdsHsrpVirtualAddr."::={ ciscoWdsInfoMobility 6}cwdsiWdsHsrpVirtualAddr OBJECT-TYPESYNTAXInetAddress(SIZE(0..36))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The vitrual Internet address of the WLSM when the HSRP
is enabled."::={ ciscoWdsInfoMobility 7}cwdsiHsrpState OBJECT-TYPESYNTAXINTEGER{unknown(1),disabled(2),
initial(3),learn(4),backup(5),speak(6),standby(7),active(8)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the state of HSRP.
unknown(1) - The state is unknown.
disabled(2) - The HSRP is disabled.
initial(3) - This is the starting state and
indicates that HSRP is not running.
learn(4) - The router is still waiting to hear
from the active router.
backup(5) - The router monitors the availability
and state of the Master Router.
speak(6) - The router sends periodic Hello
messages and is actively participating
in the election of the active and/or
standby router.
standby(7) - The router is a candidate to become
the next active router and sends
periodic Hello messages.
active(8) - The router is currently forwarding
packets that are sent to the group's
virtual MAC address. The router sends
periodic Hello messages."::={ ciscoWdsInfoMobility 8}cwdsiMobilityGroupTable OBJECT-TYPESYNTAXSEQUENCEOF CwdsiMobilityGroupEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table provides the information about mobility
network-id. When a Mobile Node associates with a
mobility enabled SSID, the Mobile Node registers with
the network and is assigned to a particular mobility
group. At the system level, a mobility network-id
internally defines this mobility group. The mobility
network-id is the mechanism the system uses to
associate the user with a particular Fast Secure
Roaming Tunnel. As the Mobile Node roams, the system
tracks user movement, making sure that the user
maintains association with the same mobility group."::={ ciscoWdsInfoMobility 9}cwdsiMobilityGroupEntry OBJECT-TYPESYNTAX CwdsiMobilityGroupEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry is a set of attributes of a Mobility
network-id currently configured in WDS."INDEX{ cwdsiMobilityGrpNetworkId }::={ cwdsiMobilityGroupTable 1}
CwdsiMobilityGroupEntry ::=SEQUENCE{
cwdsiMobilityGrpNetworkId Unsigned32,
cwdsiMobilityGrpTunnelAddrType InetAddressType,
cwdsiMobilityGrpTunnelAddr InetAddress,
cwdsiMobilityGrpTunnelMtu Unsigned32,
cwdsiMobilityGrpFlags BITS,
cwdsiMobilityGrpMnNum Gauge32}cwdsiMobilityGrpNetworkId OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This objects specifies the mobility network-id which
uniquely defines a mobility group."::={ cwdsiMobilityGroupEntry 1}cwdsiMobilityGrpTunnelAddrType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-only
STATUScurrentDESCRIPTION"Represents the type of Internet address stored in the
corresponding instance of the
cwdsiMobilityGrpTunnelAddr."::={ cwdsiMobilityGroupEntry 2}cwdsiMobilityGrpTunnelAddr OBJECT-TYPESYNTAXInetAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the Internet address of the
Mobility tunnel, which is the tunnel source address of
the mGRE tunnel on RP. Access Point uses this address
to tunnel Mobile Node traffic."::={ cwdsiMobilityGroupEntry 3}cwdsiMobilityGrpTunnelMtu OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"This object specifies the maximum transmission unit
of IP packet for the Mobility tunnel."::={ cwdsiMobilityGroupEntry 4}cwdsiMobilityGrpFlags OBJECT-TYPESYNTAXBITS{none(0),trusted(1),broadcast(2),tcpMssAdjust(3),dynamic(4),multicast(5),ipDiscovery(6)}MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"This object specifies the attributes of the mobility
tunnel.
none(0) - The mobility network-id is not
supported on L3MM.
trusted(1) - By default, a mobility network is
considered 'untrusted'. In an
untrusted network, Mobile Nodes are
required to use a DHCP-obtained IP
address. In a 'trusted' network,
Mobile Nodes are allowed to use
static IP addresses. On an untrusted
network, data forwarding path for a
Mobile Node is established and
updated by snooping DHCP packets
between the Mobile Node and the DHCP
server. On the other hand, a trusted
network data path establishment and
update is achieved by snooping IP
packets generated by the Mobile Node.
broadcast(2) - IP broadcast is allowed on the
mobility network-id corresponding to
this tunnel.
tcpMssAdjust(3)- The Access Point should do a TCP
Maximum Segment Size (MSS) adjustment
for the tunnel corresponding to the
mobility network-id.
dynamic(4) - Wireless broadcast domain
corresponding to mobility network-id
is dynamically created on an Access
Point.
multicast(5) - IP multicast is allowed on the
mobility network-id corresponding to
this tunnel.
ipDiscovery(6) - IP broadcast pings will be generated
to discover the IP address of
the wireless client."::={ cwdsiMobilityGroupEntry 5}cwdsiMobilityGrpMnNum OBJECT-TYPESYNTAXGauge32UNITS"mobile-nodes"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of Mobile Nodes
of which the mobility network-id is
cwdsiMobilityGrpNetworkId."::={ cwdsiMobilityGroupEntry 6}--********************************************************************
--* WDS Roaming Statistics
--********************************************************************cwdsiRoamStatsStartTime OBJECT-TYPESYNTAXDateAndTimeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the start time and date since
the statistics has been gathered."::={ ciscoWdsInfoRoamStatistics 1}cwdsiRoamStatsAvgFiveSeconds OBJECT-TYPESYNTAXGauge32UNITS"roams-per-second"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the system-wide average number
of roams per second for the previous 5 seconds
interval."::={ ciscoWdsInfoRoamStatistics 2}cwdsiRoamStatsAvgOneMinute OBJECT-TYPESYNTAXGauge32UNITS"roams-per-second"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the system-wide average number
of roams per second for the previous 1 minute
interval."::={ ciscoWdsInfoRoamStatistics 3}cwdsiRoamStatsAvgFiveMinutes OBJECT-TYPESYNTAXGauge32UNITS"roams-per-second"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the system-wide average number
of roams per second for the previous 5 minutes
interval."::={ ciscoWdsInfoRoamStatistics 4}cwdsiRoamMblGrpStatsTable OBJECT-TYPESYNTAXSEQUENCEOF CwdsiRoamMblGrpStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table provides the information about the roaming
statistics per the mobility network-id. Roams per
second statistics will have averages for 5 seconds,
one minute and five minutes. These data will be
separated by the mobility network-id and differentiated
by roams with 'no AAA authentications',
'AAA authentications', and 'Fast Secured
Authentications'."::={ ciscoWdsInfoRoamStatistics 5}cwdsiRoamMblGrpStatsEntry OBJECT-TYPESYNTAX CwdsiRoamMblGrpStatsEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"Each entry is a set of roaming statistics."INDEX{ cwdsiRoamMblGrpStatsNetworkId }::={ cwdsiRoamMblGrpStatsTable 1}
CwdsiRoamMblGrpStatsEntry ::=SEQUENCE{
cwdsiRoamMblGrpStatsNetworkId Unsigned32,
cwdsiRoamMblGrpStatsTotal Counter32,
cwdsiRoamMblGrpStatsNoAuthAaa Counter32,
cwdsiRoamMblGrpStatsAuthAaa Counter32,
cwdsiRoamMblGrpStatsFastSecured Counter32,
cwdsiRoamMblGrpStatsFiveSeconds Gauge32,
cwdsiRoamMblGrpStatsOneMinute Gauge32,
cwdsiRoamMblGrpStatsFiveMinutes Gauge32}cwdsiRoamMblGrpStatsNetworkId OBJECT-TYPE
SYNTAXUnsigned32(1..4096)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object specifies the mobility network-id of the
roaming Mobile Nodes."::={ cwdsiRoamMblGrpStatsEntry 1}cwdsiRoamMblGrpStatsTotal OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the count of total roams within
the mobility network-id.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiRoamStatsStartTime."::={ cwdsiRoamMblGrpStatsEntry 2}
cwdsiRoamMblGrpStatsNoAuthAaa OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the count of roams without AAA
authentications within the mobility network-id.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiRoamStatsStartTime."::={ cwdsiRoamMblGrpStatsEntry 3}cwdsiRoamMblGrpStatsAuthAaa OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the count of roams with AAA
authentications within the mobility network-id.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiRoamStatsStartTime."::={ cwdsiRoamMblGrpStatsEntry 4}cwdsiRoamMblGrpStatsFastSecured OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the count of roams with Fast
Secured authentications within the mobility
network-id.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiRoamStatsStartTime."::={ cwdsiRoamMblGrpStatsEntry 5}cwdsiRoamMblGrpStatsFiveSeconds OBJECT-TYPESYNTAXGauge32UNITS"roams-per-second"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"This object specifies the average number of roams per
second for the previous 5 seconds interval within the
mobility network-id."::={ cwdsiRoamMblGrpStatsEntry 6}cwdsiRoamMblGrpStatsOneMinute OBJECT-TYPESYNTAXGauge32UNITS"roams-per-second"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the average number of roams per
second for the previous 1 minute interval within the
mobility network-id."::={ cwdsiRoamMblGrpStatsEntry 7}cwdsiRoamMblGrpStatsFiveMinutes OBJECT-TYPESYNTAXGauge32UNITS"roams-per-second"MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"This object specifies the average number of roams per
second for the previous 5 minutes interval within the
mobility network-id."::={ cwdsiRoamMblGrpStatsEntry 8}-- ********************************************************************
-- * Notifications
-- ********************************************************************cwdsiLcpStatusChange NOTIFICATION-TYPEOBJECTS{
cwdsiLcpStatus
}STATUScurrentDESCRIPTION"This notification will be sent when a LCP status
changes from 'down' to 'up' or from 'up' to 'down'."::={ ciscoWdsInfoMIBNotifs 1}cwdsiHsrpStateChange NOTIFICATION-TYPEOBJECTS{
cwdsiHsrpState
}STATUScurrentDESCRIPTION
"This notification will be sent when HSRP state
changes from 'standby' to 'active' or from 'active' to
'standby'."::={ ciscoWdsInfoMIBNotifs 2}--********************************************************************
-- Conformance information
--********************************************************************ciscoWdsInfoMIBCompliances OBJECTIDENTIFIER::={ ciscoWdsInfoMIBConform 1}ciscoWdsInfoMIBGroups OBJECTIDENTIFIER::={ ciscoWdsInfoMIBConform 2}--********************************************************************
--* Compliance statements
--********************************************************************ciscoWdsInfoMIBCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement for the SNMP entities that
implement the cwdsiInformationMIB module."
MODULEMANDATORY-GROUPS{
ciscoWdsInfoMacAuthCacheGroup,
ciscoWdsInfoAccessPointGroup,
ciscoWdsInfoMobileNodeGroup,
ciscoWdsInfoNetworkManagerGroup,
ciscoWdsInfoStatisticsGroup,
ciscoWdsInfoMobilityGroup,
ciscoWdsInfoRoamStatisticsGroup,
ciscoWdsInfoNotifGroup
}::={ ciscoWdsInfoMIBCompliances 1}--********************************************************************
--* Units of conformance
--********************************************************************ciscoWdsInfoMacAuthCacheGroup OBJECT-GROUPOBJECTS{
cwdsiMacAuthCacheAge
}STATUScurrentDESCRIPTION"This collection of objects provide the information
about MAC addresses and ages for MAC authentication
of the device station."::={ ciscoWdsInfoMIBGroups 1}ciscoWdsInfoAccessPointGroup OBJECT-GROUPOBJECTS{
cwdsiApAddr,
cwdsiApAddrType,
cwdsiApName,
cwdsiApState,
cwdsiApLifeTime,
cwdsiApNeighborAddrType,
cwdsiApNeighborAddr,
cwdsiApNeighborName,
cwdsiApNeighborPortName
}STATUScurrentDESCRIPTION"This collection of objects provide the information
about entities of a Access Point registered with WDS."::={ ciscoWdsInfoMIBGroups 2}ciscoWdsInfoMobileNodeGroup OBJECT-GROUPOBJECTS{
cwdsiMnAddr,
cwdsiMnAddrType,
cwdsiMnApMacAddr,
cwdsiMnApAddr,
cwdsiMnApAddrType,
cwdsiMnMobilityNetworkId,
cwdsiMnState,
cwdsiMnBssid,
cwdsiMnVlan,
cwdsiMnSsid,
cwdsiMnKeyMgmt,
cwdsiMnAuthType,
cwdsiMnUptime,
cwdsiMnLifetime
}STATUScurrentDESCRIPTION"This collection of objects provide the information
about entities of Mobile Node registered with WDS."::={ ciscoWdsInfoMIBGroups 3}ciscoWdsInfoNetworkManagerGroup OBJECT-GROUPOBJECTS{
cwdsiWnmState,
cwdsiWnmLinkStatus,
cwdsiWnmClientTracking,
cwdsiWnmReqMsgCount,
cwdsiWnmSentMsgCount,
cwdsiWnmRetryTxMsgCount,
cwdsiWnmWaitingAckMsgCount,
cwdsiWnmDropMicTxMsgCount,
cwdsiWnmDropUmdTxMsgCount,
cwdsiWnmIndicatedMsgCount,
cwdsiWnmRxMsgCount,
cwdsiWnmDropRxMsgCount,
cwdsiWnmDiscontinuityTime
}STATUScurrentDESCRIPTION"This collection of objects provide the information
about the configuration status and statistics data
between WDS and Network Manager. "::={ ciscoWdsInfoMIBGroups 4}ciscoWdsInfoStatisticsGroup OBJECT-GROUPOBJECTS{
cwdsiApNum,
cwdsiMnNum,
cwdsiAaaAuthAttemptCount,
cwdsiAaaAuthSuccessCount,
cwdsiAaaAuthFailureCount,
cwdsiMacSpoofingBlockCount,
cwdsiRoamsWithoutAaaAuthCount,
cwdsiRoamsWithFullAaaAuthCount,
cwdsiRoamsFastSecuredCount,
cwdsiMscMismatchCount,
cwdsiKscFailureCount,
cwdsiMicFailureCount,
cwdsiRnMismatchCount
}STATUScurrentDESCRIPTION"This collection of objects provide the information
about the statistics of Access Points and Mobile
Nodes registered with WDS."::={ ciscoWdsInfoMIBGroups 5}ciscoWdsInfoMobilityGroup OBJECT-GROUPOBJECTS{
cwdsiLcpStatus,
cwdsiCsMgmtAddrType,
cwdsiCsMgmtAddr,
cwdsiWdsAddrType,
cwdsiWdsAddr,
cwdsiWdsHsrpVirtualAddrType,
cwdsiWdsHsrpVirtualAddr,
cwdsiHsrpState,
cwdsiMobilityGrpTunnelAddrType,
cwdsiMobilityGrpTunnelAddr,
cwdsiMobilityGrpTunnelMtu,
cwdsiMobilityGrpFlags,
cwdsiMobilityGrpMnNum
}STATUScurrentDESCRIPTION"This collection of objects provide the information
about entities of the Mobility Network."::={ ciscoWdsInfoMIBGroups 6}ciscoWdsInfoRoamStatisticsGroup OBJECT-GROUPOBJECTS{
cwdsiRoamStatsStartTime,
cwdsiRoamStatsAvgFiveSeconds,
cwdsiRoamStatsAvgOneMinute,
cwdsiRoamStatsAvgFiveMinutes,
cwdsiRoamMblGrpStatsTotal,
cwdsiRoamMblGrpStatsNoAuthAaa,
cwdsiRoamMblGrpStatsAuthAaa,
cwdsiRoamMblGrpStatsFastSecured,
cwdsiRoamMblGrpStatsFiveSeconds,
cwdsiRoamMblGrpStatsOneMinute,
cwdsiRoamMblGrpStatsFiveMinutes
}STATUScurrentDESCRIPTION"This collection of objects provide the information
about the Roaming statistics."::={ ciscoWdsInfoMIBGroups 7}ciscoWdsInfoNotifGroup NOTIFICATION-GROUPNOTIFICATIONS{
cwdsiLcpStatusChange,
cwdsiHsrpStateChange
}STATUScurrentDESCRIPTION"This collection of objects provide the notifications
about the LCP status and HSRP state."::={ ciscoWdsInfoMIBGroups 8}END